ITALIANO
CDB ENGINEERING SPA

Your Partner in filtration and process equipment

Steam Traps and steam equipment » Thermodynamic steam trap LTD42

The Thermodynamic steam trap is popular with many buyers in the industry.

Its ingenious operating principle is based on the physical Law of Bernouilli, which states that, in a moving medium, the total pressure is equal in all points. This pressure consists of static pressure and dynamic pressure and the increase of one of the components results in a decrease of the other (also called "hydrodynamic paradox"). This phenomenon can best be explained by means of a children's game, needing a cotton reel, a paper disc, and a pin.

Surprisingly it proves to be impossible to remove the disc by means of blowing into the reel. On the contrary, the harder one blows, the more the disc will move towards the reel. The cause is the greatly increased radial flow velocity (and resulting static pressure drop) in the space between disc and reel.

Thermodynamic steam traps LTD 42
Other Thermodynamic steam traps:
TD50 LTD52 LHRW150, LHR260A, LHR150A Thermodynamic steam traps LTD 42

CDB ENGINEERING SPA
 

Tel. +39 0377 912268/5

Fax +39 0377 910668

Email info@cdbengineering.com

Limiting Conditions
RatingANSI 600
PMA42 bar
TMA425°C
Max operating back pressure80%
Sizes
1/2" - 3/4" - 1"
Connections
ScrewedASME B1.20.1 (NPT) BS21 (BSP)
Socket weldASME B16.11
FlangedASME B16.5 - UNI - DIN

Main Features:

Discharges air and non condensable gases

Integral seat with hardened seating surfaces

Operates with superheated steam

Simple and compact design

Intermittent discharge

Ordering Information:

Inlet pressure

Back pressure

Operating temperature

Condensate load

End connections

Thermodynamic steam traps LTD 42
PosDescriptionMaterialsSpares
1BodyASTM 216 WCB HF seat 
2CoverASTM A105 
3ScreenSS 304X
4DiscAISI 410X
5PlugA105 
6GasketSW 304/graphiteX
Thermodynamic steam traps LTD 42
Size (inches)

H1

H2

D

SW

RF (150#)RF (300#)RF (600#)
LKgL1KgL1KgL1Kg
1/2"405438

80

0,8

1601,81702,61702,6
3/4"525950901,21702,61854,21854,2
1"5962509531805,21906,81906,8

Dimensions: H, H1, D, S are in millimeters (mm)

11/02

Installation:

The trap will operate in any position, but the preferred installation is in the horizontal plane with the cap on the top.

Isolating valve should be installed upstream and downstream of the trap for safe maintenance.

Always open isolation valve slowly until normal operating conditions are achieved to avoid system shocks.

Maintenance:

The trap can be maintained without disturbing the piping connections. Ensure that trap is isolated upstream and downstream before attempting to dismantle it. Allow the trap to cool before dismantling.

Periodic cleaning of the disc and seat will facilitate trouble free performance. Only the disc and seat are subject to wear.

A worn disc can be replaced and slight seat can be corrected by resurfacing an a lap plate.

COMPANY

PRODUCTS

INFO

Linkedin Youtube chanel

All right reserved. Copyright 2017 by CDB ENGINEERING SPA

Address: L. Maggi, 19 - 26841 Casalpusterlengo (LO) Italy

Paid up share Capital Euro 1.050.000,00 i.v.

VAT NO. 02977730965 - N. REA 1449742

Trademarks are register by their owner